haipinet
17/02/2010, 21:20
he buscado por todo sitio aver si hay algo para thomson tcw710 y nada
le conecto el cable rs232 tll y me sale esto
eCos - hal_diag_init
Init device '/dev/ttydiag'
Init tty channel: 80808f38
Init device '/dev/tty0'
Init tty channel: 80808f58
Init device '/dev/haldiag'
HAL/diag SERIAL init
Init device '/dev/ser0'
BCM 33XX SERIAL init - dev: 0.2
Set output buffer - buf: 80875408 len: 2048
Set input buffer - buf: 80875c08 len: 2048
BCM 33XX SERIAL config
0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target)
Configuring/Loading Flash driver...
0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target)
Loading ProgramStore driver...
0x0000001e [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target)
Loading BootloaderStore driver...
0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target)
Loading NonVol driver...
0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target)
Storage drivers initialized successfully.
0x00000032 [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Tar
get) Creating singletons for ProgramStore/BootloaderStore/NonVol devices...
Detecting the next image number that we will store to by default...
0x3c Computing CRC32 over image2 to ensure that it is valid...
ProgramStoreDeviceDriver::ProgramStoreDriverIsHead erValid: WARNING - ProgramSto
re header HCS check failed!
ProgramStoreDeviceDriver::ProgramStoreDriverIsImag eValid: WARNING - Header isn'
t valid!
0x3c Done computing CRC32!
By default, we will dload to image number 2!
By default, we will dload to block number 0!
0x00000046 [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Tar
get) Device abstraction singletons created successfully.
Function: SetHardcodeVendorProfile
The ProfileMagic of image is not equal to 0xFFAAAAFF!!!
0x0000005a [tStartup] BcmCmBpiNonVolSettings::BcmCmBpiNonVolSettings: (Euro-Doc
sis CM BPI NonVol Settings) WARNING - Singleton pointer is not NULL! There are
multiple instances! Leaving the singleton pointer alone...
Reading Permanent settings from non-vol...
Checksum for permanent settings: 0x46fe0605
Settings were read and verified.
Reading Dynamic settings from non-vol...
Checksum for dynamic settings: 0xbf8da5df
Settings were read and verified.
Creating SNMP agent cablemodem agent
DON'T think we need to go here - so don't:::: init_mib !!!!
WARNING: netsnmp_brcm_create_tstring called with no address!
If you pressed the 's' key before this point, we will skip driver initialization
...
Creating DOCSIS Control Thread...
le conecto el cable rs232 tll y me sale esto
eCos - hal_diag_init
Init device '/dev/ttydiag'
Init tty channel: 80808f38
Init device '/dev/tty0'
Init tty channel: 80808f58
Init device '/dev/haldiag'
HAL/diag SERIAL init
Init device '/dev/ser0'
BCM 33XX SERIAL init - dev: 0.2
Set output buffer - buf: 80875408 len: 2048
Set input buffer - buf: 80875c08 len: 2048
BCM 33XX SERIAL config
0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target)
Configuring/Loading Flash driver...
0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target)
Loading ProgramStore driver...
0x0000001e [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target)
Loading BootloaderStore driver...
0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target)
Loading NonVol driver...
0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target)
Storage drivers initialized successfully.
0x00000032 [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Tar
get) Creating singletons for ProgramStore/BootloaderStore/NonVol devices...
Detecting the next image number that we will store to by default...
0x3c Computing CRC32 over image2 to ensure that it is valid...
ProgramStoreDeviceDriver::ProgramStoreDriverIsHead erValid: WARNING - ProgramSto
re header HCS check failed!
ProgramStoreDeviceDriver::ProgramStoreDriverIsImag eValid: WARNING - Header isn'
t valid!
0x3c Done computing CRC32!
By default, we will dload to image number 2!
By default, we will dload to block number 0!
0x00000046 [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Tar
get) Device abstraction singletons created successfully.
Function: SetHardcodeVendorProfile
The ProfileMagic of image is not equal to 0xFFAAAAFF!!!
0x0000005a [tStartup] BcmCmBpiNonVolSettings::BcmCmBpiNonVolSettings: (Euro-Doc
sis CM BPI NonVol Settings) WARNING - Singleton pointer is not NULL! There are
multiple instances! Leaving the singleton pointer alone...
Reading Permanent settings from non-vol...
Checksum for permanent settings: 0x46fe0605
Settings were read and verified.
Reading Dynamic settings from non-vol...
Checksum for dynamic settings: 0xbf8da5df
Settings were read and verified.
Creating SNMP agent cablemodem agent
DON'T think we need to go here - so don't:::: init_mib !!!!
WARNING: netsnmp_brcm_create_tstring called with no address!
If you pressed the 's' key before this point, we will skip driver initialization
...
Creating DOCSIS Control Thread...