[ Tutorial ] Desempolvar nuestros queridos Thomson TCW710

**Judokan** · 27/10/2010, 12:57

Para conelcarro:

LA flash es la que esta al lado de la tarjeta inalambrica pero si te das un poco de cuenta veras que la que esta al lado de la tarjeta inalambrica no tiene patillas para poder hacerle el corto.
Un saludo

**conelcarro** · 27/10/2010, 20:11

Necesitas estar Registrado y Logueado para ver el contenido...

yo decia la k esta debajo de la inalambrica k pone flash pero si es la de al lado ire haciendo cortos .

**conelcarro** · 27/10/2010, 21:12

bueno pues estoi haciendo cortos en las dos patillas k tu dices k supongo k son las que tu dices claro te e subido una foto haber si lo estoi haciendo bien .

Necesitas estar Registrado y Logueado para ver el contenido...

.

i un saludo.

**mijaenlla** · 27/10/2010, 21:22

Necesitas estar Registrado y Logueado para ver el contenido...

Una imagen dice mas que mil palabras,

,solo me queda saber donde conecto el cable de serie.
Saludos

**duna** · 27/10/2010, 21:45

Necesitas estar Registrado y Logueado para ver el contenido...

NO
El chip de la flash siempre tiene los pin en las caras pekeñas del rectangulo.
Lo ke sale en tu foto es el ram

PD: por lo ke dices tu 710 tiene una trageta mini-pci wifi, como el 2320r2. Si es asi hay varias revisiones de 710, por ke el mio esta integrada

**conelcarro** · 27/10/2010, 22:03

si la ttarjeta integrada es la k sale justo al lado de lo k es la ram entonces la flash es este modelo la k tu tienes TE28F640 FLASH INTEL? I donde le tendria k hacer el corto si miro el chip defrente i en un lado me sale el nombre intel i en el otro me pone flash el corto en que lao iria i arriba o abajo ?

**duna** · 27/10/2010, 22:39

Necesitas estar Registrado y Logueado para ver el contenido...

Yo tengo flash samsug ke es la misma ke judokan explica
La intel TE28F640 es tsop 56 pins, habria ke mirar el datasheet.
El pin "1" esta indicado con un circulo brillante muy pekeño

**conelcarro** · 27/10/2010, 23:00

eso buscava yo un circulo en una esquina pero resulta k lo tiene en las 4 esquinas supongo k con este chip no se podra hacer ire probando haber.

.

**conelcarro** · 28/10/2010, 08:13

k modelo de flash samsumg es me lo podrias poner porfavor.

i un saludo.

**Judokan** · 28/10/2010, 19:39

Vamos por partes, da igual la flash que sea, yo lo he probado con distintas flash y en todas funciona el metodo, y pasa saber cual es la patilla 1 mirar la serigrafia de color blanco que lo pone y tambien decir que las flashes que se montan en los 710 son tsop48 y no tsop56 como en los webstar2320r2.
Un saludo

**conelcarro** · 28/10/2010, 21:53

duna tiene razon esta es un tsop 56 vamos creo yo eso pone en su especificadiones esta es la que tengo yo exactamente

Necesitas estar Registrado y Logueado para ver el contenido...

de todas las maneras buscare de todas las maneras haber si me podeis decir el model de flash k es la samsumng.

i un saludo.

**conelcarro** · 29/10/2010, 03:27

una pregunta por cable blackat se pued eatacar a este modem?

i un saludo.

**Judokan** · 29/10/2010, 20:36

No.

**conelcarro** · 30/10/2010, 01:01

al final hice el cable serie i se lo puse al modem i bueno no entiendo mucho pero cuando arranco el modem normal con la inalambrica i todo k ya digo k el mio tiene la inalambrica en tarjeta como el 2320r2 me sale este log
eCos - hal_diag_init
Init device '/dev/ttydiag'
Init tty channel: 80808f38
Init device '/dev/tty0'
Init tty channel: 80808f58
Init device '/dev/haldiag'
HAL/diag SERIAL init
Init device '/dev/ser0'
BCM 33XX SERIAL init - dev: 0.2
Set output buffer - buf: 80875408 len: 2048
Set input buffer - buf: 80875c08 len: 2048
BCM 33XX SERIAL config
0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Configuring/Loading Flash driver...
0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading ProgramStore driver...
0x0000001e [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading BootloaderStore driver...
0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading NonVol driver...
0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Storage drivers initialized successfully.
0x00000032 [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Creating singletons for ProgramStore/BootloaderStore/NonVol devices...
Detecting the next image number that we will store to by default...
0x3c Computing CRC32 over image2 to ensure that it is valid...
ProgramStoreDeviceDriver::ProgramStoreDriverIsImag eValid: WARNING - Image CRC failed!
0x168 Done computing CRC32!
By default, we will dload to image number 2!

By default, we will dload to block number 0!

0x00000168 [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Device abstraction singletons created successfully.

Function: SetHardcodeVendorProfile
The ProfileMagic of image is not equal to 0xFFAAAAFF!!!
0x0000017c [tStartup] BcmCmBpiNonVolSettings::BcmCmBpiNonVolSettings: (Euro-Docsis CM BPI NonVol Settings) WARNING - Singleton pointer is not NULL! There are multiple instances! Leaving the singleton pointer alone...

Reading Permanent settings from non-vol...
Checksum for permanent settings: 0x2cdc5bb1
Settings were read and verified.

Reading Dynamic settings from non-vol...
Checksum for dynamic settings: 0x7c0b4b65
Settings were read and verified.

Creating SNMP agent cablemodem agent
cablemodem agent disabling management.
cablemodem agent defering traps.
DON'T think we need to go here - so don't:::: init_mib !!!!
WARNING: netsnmp_brcm_create_tstring called with no address!

If you pressed the 's' key before this point, we will skip driver initialization...
Creating DOCSIS Control Thread...

i cuando desconecto la inalambrica me sale este otro:
eCos - hal_diag_init
Init device '/dev/ttydiag'
Init tty channel: 80808f38
Init device '/dev/tty0'
Init tty channel: 80808f58
Init device '/dev/haldiag'
HAL/diag SERIAL init
Init device '/dev/ser0'
BCM 33XX SERIAL init - dev: 0.2
Set output buffer - buf: 80875408 len: 2048
Set input buffer - buf: 80875c08 len: 2048
BCM 33XX SERIAL config
0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Configuring/Loading Flash driver...
0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading ProgramStore driver...
0x0000001e [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading BootloaderStore driver...
0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading NonVol driver...
0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Storage drivers initialized successfully.
0x00000032 [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Creating singletons for ProgramStore/BootloaderStore/NonVol devices...
Detecting the next image number that we will store to by default...
0x3c Computing CRC32 over image2 to ensure that it is valid...
ProgramStoreDeviceDriver::ProgramStoreDriverIsImag eValid: WARNING - Image CRC failed!
0x168 Done computing CRC32!
By default, we will dload to image number 2!

By default, we will dload to block number 0!

0x00000168 [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Device abstraction singletons created successfully.

Function: SetHardcodeVendorProfile
The ProfileMagic of image is not equal to 0xFFAAAAFF!!!
0x0000017c [tStartup] BcmCmBpiNonVolSettings::BcmCmBpiNonVolSettings: (Euro-Docsis CM BPI NonVol Settings) WARNING - Singleton pointer is not NULL! There are multiple instances! Leaving the singleton pointer alone...

Reading Permanent settings from non-vol...
Checksum for permanent settings: 0x2cdc5bb1
Settings were read and verified.

Reading Dynamic settings from non-vol...
Checksum for dynamic settings: 0x7c0a4b65
Settings were read and verified.

Creating SNMP agent cablemodem agent
cablemodem agent disabling management.
cablemodem agent defering traps.
DON'T think we need to go here - so don't:::: init_mib !!!!
WARNING: netsnmp_brcm_create_tstring called with no address!

If you pressed the 's' key before this point, we will skip driver initialization...
Creating DOCSIS Control Thread...
Current time is 01/01/1970 00:00:04

>>> YIKES... looks like you may have a problem! <<<

Task: tStartup
---------------------------------------------------
ID: 0x0005
Handle: 0x8083fe08
Set Priority: 18
Current Priority: 18
State: SUSP
Stack Base: 0x80833e08
Stack Size: 12288 bytes
Stack Used: 5208 bytes

r0/zero=00000000 r1/at =00000000 r2/v0 =80590c4c r3/v1 =80590e38
r4/a0 =00000000 r5/a1 =00000000 r6/a2 =34003730 r7/a3 =00653038
r8/t0 =00836411 r9/t1 =00000008 r10/t2 =00000001 r11/t3 =00000000
r12/t4 =00000000 r13/t5 =00000000 r14/t6 =27bdfff0 r15/t7 =8059343c
r16/s0 =8083fe08 r17/s1 =80ff422c r18/s2 =00000000 r19/s3 =80870000
r20/s4 =80870000 r21/s5 =80760000 r22/s6 =11110016 r23/s7 =11110017
r24/t8 =80836451 r25/t9 =00000002 r26/k0 =00000001 r27/k1 =00000000
r28/gp =00000000 r29/sp =808364e0 r30/fp =80836dd0 r31/ra =80018e60

PC : 0x80018e60 error addr: 0x80018e2c
cause: 0x8083fe08 status: 0x1000ff00

BCM interrupt enable: ecffffdf, status: 00000000

entry 80018dc8 called from 80592bac
entry 80592b80 called from 8035d708
entry 8035d370 called from 80594474
entry 80594464 called from 80594140
entry 8059411c called from 805944a4
entry 80594494 called from 8059e164
entry 8059e154 called from 800103e0
entry 800103bc Return address (00000000) invalid or not found. Trace stops.
Stack Stack Stack
TaskId TaskName Priority State Size Used Margin
---------- -------------------------------- -------- -------- -------- -------- --------
0x80876540 Idle Thread 31 RUN 2048 608 1440
0x808f9f20 Network alarm support 6 SLEEP 2256 448 1808
0x80879218 Network support 7 SLEEP 8192 304 7888
0x808fac70 pthread.00000800 15 EXIT 7852 1104 6748
0x8083fe08 tStartup 18 SUSP 12288 5208 7080
0x80ff334c NonVol Device Async Helper 25 SLEEP 3072 516 2556
0x80fcc9e0 ThomLedThread 21 SLEEP 4096 1056 3040
0x80fcf2e0 CableHome Ping Thread 29 SLEEP 6144 480 5664
0x80ff422c WDOG 17 RUN 5120 1588 3532
0x80ff4324 VBrd 21 SLEEP 4096 352 3744
0x80f98750 BFC Ping Thread 29 SLEEP 6144 604 5540
0x80fc4d30 ConsoleThread 27 SUSP 24576 436 24140
0x80f7c0f4 CfgVB Thread 23 SLEEP 4096 512 3584
0x80f7aaa4 DHCM 25 SLEEP 16384 504 15880
0x80f94858 Event Log Thread 25 RUN 8192 896 7296
0x80f4d964 Time Of Day Thread 23 SLEEP 6144 464 5680
0x80f4ddd0 CmDocsisIpThread 23 SLEEP 8192 512 7680
0x80f48704 CmBpiManagerThd 25 SLEEP 8192 504 7688
0x80f44b90 CmDsxHelper 23 SLEEP 8192 724 7468
0x80f60f58 CmDocsisCtlThread 21 SLEEP 8192 516 7676
0x80f3dab0 Scan Downstream Thread 23 SLEEP 4096 512 3584
0x80f3c450 RateShaping Thread 23 SLEEP 4096 444 3652
0x80ff441c CMHL 23 SLEEP 4500 376 4124
0x80ff4514 CMHH 21 SLEEP 4500 360 4140
0x80ff460c ENRX 23 SLEEP 4500 356 4144
0x80ff4704 ENTX 23 SLEEP 4500 344 4156
0x80ff47fc ELNK 23 SLEEP 4500 328 4172
0x80ff48f4 USTX 23 SLEEP 4500 348 4152
0x80ff49ec USRX 23 SLEEP 4500 380 4120
0x80ff4ae4 UBCT 19 SLEEP 4500 364 4136
0x80ff4bdc USRN 23 SLEEP 4500 348 4152
0x80d35f8c DHCP Client Thread 23 SLEEP 8192 516 7676
0x80ff4cd4 IpHalIst 23 SLEEP 4500 628 3872
0x80d2f66c CmPropaneCtlThread 23 SLEEP 8192 1608 6584
0x80d2c9e8 IGMP Thread 23 SLEEP 4096 468 3628
0x80d2b060 NetToMedia Thread 23 SLEEP 4096 508 3588
0x80d25f48 Trap Thread 23 SLEEP 16384 516 15868
0x80ff3dcc SNMP Thread 23 SLEEP 17408 840 16568
0x80c371b0 VendorCmAppCtlThread 23 SLEEP 8192 516 7676
Done!
Thomson CM Event Log initializing with stored events.
Event log initialization complete.
eCos - hal_diag_init
Init device '/dev/ttydiag'
Init tty channel: 80808f38
Init device '/dev/tty0'
Init tty channel: 80808f58
Init device '/dev/haldiag'
HAL/diag SERIAL init
Init device '/dev/ser0'
BCM 33XX SERIAL init - dev: 0.2
Set output buffer - buf: 80875408 len: 2048
Set input buffer - buf: 80875c08 len: 2048
BCM 33XX SERIAL config
0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Configuring/Loading Flash driver...
0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading ProgramStore driver...
0x0000001e [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading BootloaderStore driver...
0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading NonVol driver...
0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Storage drivers initialized successfully.
0x00000032 [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Creating singletons for ProgramStore/BootloaderStore/NonVol devices...
Detecting the next image number that we will store to by default...
0x3c Computing CRC32 over image2 to ensure that it is valid...
ProgramStoreDeviceDriver::ProgramStoreDriverIsImag eValid: WARNING - Image CRC failed!
0x168 Done computing CRC32!
By default, we will dload to image number 2!

By default, we will dload to block number 0!

0x00000168 [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Device abstraction singletons created successfully.

Function: SetHardcodeVendorProfile
The ProfileMagic of image is not equal to 0xFFAAAAFF!!!
0x0000017c [tStartup] BcmCmBpiNonVolSettings::BcmCmBpiNonVolSettings: (Euro-Docsis CM BPI NonVol Settings) WARNING - Singleton pointer is not NULL! There are multiple instances! Leaving the singleton pointer alone...

Reading Permanent settings from non-vol...
Checksum for permanent settings: 0x2cdc5bb1
Settings were read and verified.

Reading Dynamic settings from non-vol...
Checksum for dynamic settings: 0x7c094b65
Settings were read and verified.

Creating SNMP agent cablemodem agent
cablemodem agent disabling management.
cablemodem agent defering traps.
DON'T think we need to go here - so don't:::: init_mib !!!!
WARNING: netsnmp_brcm_create_tstring called with no address!

If you pressed the 's' key before this point, we will skip driver initialization...
Creating DOCSIS Control Thread...
Current time is 01/01/1970 00:00:04

>>> YIKES... looks like you may have a problem! <<<

Task: tStartup
---------------------------------------------------
ID: 0x0005
Handle: 0x8083fe08
Set Priority: 18
Current Priority: 18
State: SUSP
Stack Base: 0x80833e08
Stack Size: 12288 bytes
Stack Used: 5208 bytes

r0/zero=00000000 r1/at =00000000 r2/v0 =80590c4c r3/v1 =80590e38
r4/a0 =00000000 r5/a1 =00000000 r6/a2 =34003730 r7/a3 =00653038
r8/t0 =00836411 r9/t1 =00000008 r10/t2 =00000001 r11/t3 =00000000
r12/t4 =00000000 r13/t5 =00000000 r14/t6 =27bdfff0 r15/t7 =8059343c
r16/s0 =8083fe08 r17/s1 =80ff422c r18/s2 =00000000 r19/s3 =80870000
r20/s4 =80870000 r21/s5 =80760000 r22/s6 =11110016 r23/s7 =11110017
r24/t8 =80836451 r25/t9 =00000002 r26/k0 =00000001 r27/k1 =00000000
r28/gp =00000000 r29/sp =808364e0 r30/fp =80836dd0 r31/ra =80018e60

PC : 0x80018e60 error addr: 0x80018e2c
cause: 0x8083fe08 status: 0x1000ff00

BCM interrupt enable: ecffffdf, status: 00000000

entry 80018dc8 called from 80592bac
entry 80592b80 called from 8035d708
entry 8035d370 called from 80594474
entry 80594464 called from 80594140
entry 8059411c called from 805944a4
entry 80594494 called from 8059e164
entry 8059e154 called from 800103e0
entry 800103bc Return address (00000000) invalid or not found. Trace stops.
Stack Stack Stack
TaskId TaskName Priority State Size Used Margin
---------- -------------------------------- -------- -------- -------- -------- --------
0x80876540 Idle Thread 31 RUN 2048 608 1440
0x808f9f20 Network alarm support 6 SLEEP 2256 448 1808
0x80879218 Network support 7 SLEEP 8192 304 7888
0x808fac70 pthread.00000800 15 EXIT 7852 1104 6748
0x8083fe08 tStartup 18 SUSP 12288 5208 7080
0x80ff334c NonVol Device Async Helper 25 SLEEP 3072 516 2556
0x80fcc9e0 ThomLedThread 21 SLEEP 4096 1056 3040
0x80fcf2e0 CableHome Ping Thread 29 SLEEP 6144 480 5664
0x80ff422c WDOG 17 RUN 5120 1732 3388
0x80ff4324 VBrd 21 SLEEP 4096 352 3744
0x80f98750 BFC Ping Thread 29 SLEEP 6144 476 5668
0x80fc4d30 ConsoleThread 27 SUSP 24576 436 24140
0x80f7c0f4 CfgVB Thread 23 SLEEP 4096 512 3584
0x80f7aaa4 DHCM 25 SLEEP 16384 504 15880
0x80f94858 Event Log Thread 25 RUN 8192 896 7296
0x80f4d964 Time Of Day Thread 23 SLEEP 6144 464 5680
0x80f4ddd0 CmDocsisIpThread 23 SLEEP 8192 512 7680
0x80f48704 CmBpiManagerThd 25 SLEEP 8192 504 7688
0x80f44b90 CmDsxHelper 23 SLEEP 8192 740 7452
0x80f60f58 CmDocsisCtlThread 21 SLEEP 8192 516 7676
0x80f3dab0 Scan Downstream Thread 23 SLEEP 4096 512 3584
0x80f3c450 RateShaping Thread 23 SLEEP 4096 444 3652
0x80ff441c CMHL 23 SLEEP 4500 376 4124
0x80ff4514 CMHH 21 SLEEP 4500 360 4140
0x80ff460c ENRX 23 SLEEP 4500 356 4144
0x80ff4704 ENTX 23 SLEEP 4500 344 4156
0x80ff47fc ELNK 23 SLEEP 4500 328 4172
0x80ff48f4 USTX 23 SLEEP 4500 348 4152
0x80ff49ec USRX 23 SLEEP 4500 380 4120
0x80ff4ae4 UBCT 19 SLEEP 4500 364 4136
0x80ff4bdc USRN 23 SLEEP 4500 348 4152
0x80d35f8c DHCP Client Thread 23 SLEEP 8192 516 7676
0x80ff4cd4 IpHalIst 23 SLEEP 4500 364 4136
0x80d2f66c CmPropaneCtlThread 23 SLEEP 8192 1608 6584
0x80d2c9e8 IGMP Thread 23 SLEEP 4096 468 3628
0x80d2b060 NetToMedia Thread 23 SLEEP 4096 692 3404
0x80d25f48 Trap Thread 23 SLEEP 16384 516 15868
0x80ff3dcc SNMP Thread 23 SLEEP 17408 840 16568
0x80c371b0 VendorCmAppCtlThread 23 SLEEP 8192 516 7676
Done!
Thomson CM Event Log initializing with stored events.
Event log initialization complete.

mi pregunta es si alguno de estos dos logs os coinciden de alguna manera con el vuestro i si podeis ecxplicar asin un poco lo k esta haciendo i perdon por el peazo de log k os e puesto no sabia k copiar i lo copie todo.

i un saludo.

**Dj_Zeta** · 30/10/2010, 16:06

Y le pueden activar el factory mode sin necesidad de puentear los pines de la flash??.

Hola No registrado!!

Hi No registrado!!

Tema: [ Tutorial ] Desempolvar nuestros queridos Thomson TCW710

Herramientas

Permisos de publicación

Opciones

Enlaces Relacionados

Acerca de

Social Media